Golf Simulator Cabins
B2B private-label timber cabin shells for golf simulator bay planning. Nine standard sizes plus bespoke options; dealers confirm golfer profile, simulator hardware route, screen and enclosure layout, mat build-up and local-authority review before quoting.
Prepare a golf simulator cabin brief
Eurodita supplies the timber building shell. Simulator equipment, technology selection, internal specialist fit-out and local approvals remain outside the standard shell scope unless separately agreed in writing.
- Space: required internal clear width, length and height
- Shell: wall specification, roof form, doors and window openings
- Project: equipment clearances, destination, quantity and required timing
Share the equipment supplier's clearance requirements together with the building brief so the shell can be checked against the intended layout.
Send a simulator cabin brief
Private-label timber cabin shells for golf simulator installations. A steep apex roof reaches a 3640mm ridge, giving roughly 3.4m of internal centreline clearance for simulator fit-out planning. Nine standard sizes run from 4.3 by 3.2m to 7.5 by 4.0m; bespoke dimensions are qualified and quoted individually against drawings, engineering scope, production planning and logistics. Eurodita manufactures the agreed timber shell; simulator equipment and customer-facing presentation are managed by the trade partner within the agreed order scope.
Golf simulator shell
Apex-roof shell for simulator fit-out planning
Illustrative example fit-out, partner-installed
Screen wall planning
Door and opening layout can be planned around the screen wall
Illustrative example fit-out, partner-installed
Private-label supply
Private-label timber shell for partner-installed simulator rooms
Illustrative example fit-out, partner-installedApex height, not excavation
There are two ways to reach the head-height target a golf simulator project may need: lower the floor by excavating, or raise the roof. Eurodita raises the roof. The apex design supports head-height planning above ground level, with no excavation, no below-ground drainage or damp considerations, and no change to the above-ground footprint used in permitted-development calculations. The ridge reaches 3640mm and the eaves sit at 2405mm across the standard range.
The internal clearance is roughly 3.4m at the centreline on the standard golf simulator cabin profile. Dealers and fit-out partners should check the final swing, screen, projector and launch-monitor layout against the selected simulator equipment and the project brief. For the full height breakdown by model, see our ceiling height guide.
The range
Nine standard sizes share the same engineered height and 70mm solid, slow-grown northern European spruce walls, with FSC chain-of-custody on record. Wall specification, openings and other options are confirmed for the exact order. The two largest models include factory windows, and the largest carries a second door.
| Model | Internal (mm) | Floor area | Ridge | Eaves | Openings |
|---|---|---|---|---|---|
| 4.3 × 3.2m | 4300 × 3200 | 13.8 m² | 3640mm | 2405mm | 1 double door |
| 5.0 × 3.0m | 5000 × 3000 | 15.0 m² | 3640mm | 2405mm | 1 double door |
| 5.0 × 3.6m | 5000 × 3600 | 18.0 m² | 3640mm | 2405mm | 1 double door |
| 5.0 × 4.0m | 5000 × 4000 | 20.0 m² | 3640mm | 2405mm | 1 double door |
| 5.3 × 3.8m | 5300 × 3800 | 20.1 m² | 3640mm | 2405mm | 1 double door |
| 6.0 × 4.0m | 6000 × 4000 | 24.0 m² | 3640mm | 2405mm | 1 double door |
| 6.0 × 4.5m | 6000 × 4500 | 27.0 m² | 3640mm | 2405mm | 1 double door |
| 7.0 × 4.0m | 7000 × 4000 | 28.0 m² | 3640mm | 2405mm | 1 double door, 2 windows |
| 7.5 × 4.0m | 7500 × 4000 | 30.0 m² | 3640mm | 2405mm | 2 double doors, 2 windows |
| Bespoke | custom | to specification | to specification | to specification | to specification |
Shell supply for fitting companies
Eurodita is a B2B private-label timber building manufacturer. Eurodita manufactures the agreed timber shell; the simulator technology, screen, projector and interior fit-out are specified and installed by the fitting company or project partner. The trade partner manages the customer-facing offer within the agreed order scope. Private-label presentation, packing and customer-facing documentation are agreed per order. Standard terms are EXW (Ex Works) from Kaunas, and delivered options can be arranged for selected markets and projects, agreed individually per order. Read more about the private-label manufacturing model and the dealer programme, or review our certifications and compliance. For trade terms in full, see our shell supply guide for fitting companies.
Customisation options
Standard models can be reviewed for door, window and opening-layout changes to suit the screen wall and entry point. Some images show an example configuration; the standard specification is listed in the table above. Bespoke dimensions and other changes are qualified and quoted individually against drawings, engineering scope, production planning and logistics through the private-label route. Order quantity, pricing and production scope for standard models are confirmed per quote. Installation and foundation guidance is covered in our construction guides.
Frequently Asked Questions
What internal ceiling height does a golf simulator cabin provide?
The apex roof reaches a 3640mm ridge, giving approximately 3.4m of internal clearance at the centreline on the standard golf simulator cabin profile. The eaves sit at 2405mm. Dealers and fit-out partners should confirm the final swing, screen, projector and launch-monitor layout against the selected simulator equipment and project brief.
Can a golf simulator cabin be supplied under our own brand?
Yes. Eurodita supplies the timber shell for trade partners through a private-label manufacturing arrangement. Private-label presentation, packing and customer-facing documentation are agreed per order. The trade partner manages the simulator technology and customer-facing offer within the agreed order scope. See the private-label arrangement for terms.
What is the lead time for a golf simulator cabin order?
Production timing is confirmed in the written quotation and order. Standard terms are Ex Works (EXW) from Kaunas, Lithuania. DAP or DDP may be arranged for selected markets and projects, agreed individually per order. Full terms are in the shipping and delivery policy.
Do golf simulator cabins need planning permission in the UK?
Planning status is site-specific and not determined by construction material. Under the Town and Country Planning (General Permitted Development) (England) Order 2015, an outbuilding with a dual-pitched roof can fall within permitted development when sited more than 2 metres from a boundary, subject to a 4 metre ridge limit and a 2.5 metre eaves limit. Within 2 metres of a boundary the overall height limit is 2.5 metres, which this range exceeds, so planning permission would be required in that position. Conservation areas and listed buildings carry additional restrictions. Installers should confirm permitted-development status with the local planning authority for each site.
Can we order a bespoke size or customise the layout?
Eurodita can review custom door positions, added windows, wall-thickness options and bespoke dimensions beyond the nine standard sizes. Order quantity, pricing and production scope for standard models are confirmed per quote. Bespoke dimensions are qualified and quoted individually against drawings, engineering scope, production planning and logistics. Eurodita has manufactured timber buildings from its Kaunas factory since 1994.
Is Eurodita a bespoke golf simulator cabin manufacturer?
Yes. Eurodita supplies standard and bespoke timber cabin shells for golf simulator cabin projects through a B2B private-label manufacturing arrangement. The simulator technology, screen, projector and interior fit-out are specified and installed by the dealer, fitting company or project partner.
Can Eurodita prepare CAD or 3D quotation material for bespoke golf simulator cabins?
Eurodita supplies B2B timber shells for golf simulator cabin projects. Dealers, fit-out partners and project suppliers can send target dimensions, internal-clearance needs and door or window positions for project review. For a bespoke brief, Eurodita reviews the available drawings, scope and destination; quotation-support timing is confirmed with the team.
Related resources for dealers
-
Private-label timber manufacturing
How the private-label shell-supply model works for fitting companies and dealers
-
Dealer programme
Partnership structure, terms and onboarding for B2B partners
-
Certifications and compliance
FSC chain-of-custody, warranty and material provenance
-
Garden offices
Adjacent high-velocity category in the same private-label range
Not in the range? Build it bespoke.
Qualified bespoke production is available for selected Golf Simulator Cabins projects. Send your drawing and Eurodita will confirm fit, scope and specification.
- 1 Send a drawing A hand sketch can start the review. Mark known window and door positions, wall thickness and heights; Eurodita confirms any missing technical inputs.
- 2 Confirm the quotation scope If the enquiry fits, pricing and any CAD/3D or technical material are prepared to the agreed scope.
- 3 Review the agreed scope Revisions follow the quotation and project scope until written sign-off.
CAD/3D quotation material is prepared to the qualified project scope. Availability and timing are confirmed during qualification. Partner branding is applied where agreed; required manufacturer, legal and traceability information is retained.
Send a bespoke briefBespoke production timing is confirmed in the written quotation and order. Dealers can review private-label manufacturing and published projects.